The set AJ6-800 Advanced AirJib consists of the copter AF6-800 in combination with the gimbal CM-M in its 3-axes version. This configuration is best suited for professional aerial photography with high quality demands. With the Advanced AirJib and an appropriate camera at a minimum take-off weight (under 5kg) you will be able to record footage suitable for TV and cinema.

The gimbal used is of the CM-M-G3D make, which is a 3-axes gimbal with two motors for the pitch axis (double pitch drive). The camera mount is ideal for cameras such as the Sony A7 or the Panasonic Lumix GH4.

Since the gimbal can be rotated completely independently around the copter's main axis by 360° we have fitted the set with the landing gear AF6-800-LGG which is permanently attached and thereby follows exactly the gimbal's movements.

The damping system used is our AF6-800-DPG. Since no landing gear is attached to the copter itself there is room for the battery holders AF6-800-BHG to be installed directly on the lower centerplate.

In the configuration of our Advanced AirJib both copter and gimbal are two completely separate and independent systems. Therefore we recommend it for operation by two people with one taking over the role of the pilot and the other that of the cameraman.

The Advanced AirJib consists of the following components.

• AF6-800-FRM (base frame)
• AF6-800-PDB (power distribution board)
• AF6-800-LGG (landing gear)
• AF6-800-BHG (battery holder)
• AF6-800-DPG (damping system)
• CM-M-G3D (gimbal G3D)
• CM-M-GAA (gimbal adapter type A)
• CM-M-COA (controller holder type A)
• CM-M-CAA (camera holder type A)

Important information
Basecam Alexmos brushless gimbal electronics is not included!

Technical Specifications
Weight: 1599g
Dimensions (L x B x H): 846 x 846 x 380mm

Delivery Contents
1 piece AF6-800-FRM (base frame)
1 piece AF6-800-PDB (power distribution board)
1 piece AF6-800-LGG (landing gear)
1 piece AF6-800-BHG (battery holder)
1 piece AF6-800-DPG (damping system)
1 piece CM-M-G3D (gimbal G3D)
1 piece CM-M-GAA (gimbal adapter type A)
1 piece CM-M-COA (controller holder type A)
1 piece CM-M-CAA (camera holder type A)

Recommended Drives
T-Motor MN3110 KV470 with T-Motor 15x5.0" CFK propeller and T-Motor ESC T40A, 2 4S LiPo 5000mAh
T-Motor MN3508 KV580 with T-Motor 14x4.8" CFK propeller and T-Motor ESC T40A, 2 4S LiPo 5000mAh
T-Motor MN3510 KV700 with T-Motor 13x4.4" CFK propeller and T-Motor ESC T40A, 2 4S LiPo 5000mAh

The set AJ6-800 Basic AirJib consists of the copter AF6-800 in combination with the CM-M gimbal in its 2-axes version. This configuration is very well suited for beginners just starting to explore the world of aerial photography.

For this set we decided on the simplest version CM-M-G2S of our gimbal, which is a 2-axes gimbal with a motor for the pitch axis (single pitch drive). This camera mount is ideal for lightweight cameras such as a Sony Nex5/7 or a Blackmagic Pocket.

Since the gimbal has only two axes the copter has been fitted with the permanently attached landing gear AF6-800-LGC.

The damping system used is our AF6-800-DPC.

One advantage to a copter with a 2-axes gimbal is that its operation ordinarily only requires one person. However, it is recommended that the pilot has the option of swiveling the camera vertically up- or downwards via his own channel.

An upgrade to the AJ6-800 Advanced AirJib set is possible at any time.

The Basic AirJib consists of the following components.

• AF6-800-FRM (base frame)
• AF6-800-PDB (power distribution board)
• AF6-800-LGC (landing gear)
• AF6-800-BHC (battery holder)
• AF6-800-DPC (damping system)
• AF6-800-GMP (gimbal mounting plate)
• CM-M-G2S (gimbal G2S)
• CM-M-GAA (gimbal adapter type A)
• CM-M-COB (controller holder type B)
• CM-M-CAA (camera holder type A)

Important information
Basecam Alexmos brushless gimbal electronics is not included!

Technical Specifications
Weight: 1411g
Dimensions (L x B x H): 846 x 846 x 376mm

Delivery Contents
1 piece AF6-800-FRM (base frame)
1 piece AF6-800-PDB (power distribution board)
1 piece AF6-800-LGC (landing gear)
1 piece AF6-800-BHC (battery holder)
1 piece AF6-800-DPC (damping system)
1 piece AF6-800-GMP (gimbal mounting plate)
1 piece CM-M-G2S (gimbal G2S)
1 piece CM-M-GAA (gimbal adapter type A)
1 piece CM-M-COB (controller holder type B)
1 piece CM-M-CAA (camera holder type A)

Recommended Drives
T-Motor MN3110 KV470 with T-Motor 15x5.0" CFK propeller and T-Motor ESC T40A, 2 4S LiPo 5000mAh
T-Motor MN3508 KV580 with T-Motor 14x4.8" CFK propeller and T-Motor ESC T40A, 2 4S LiPo 5000mAh
T-Motor MN3510 KV700 with T-Motor 13x4.4" CFK propeller and T-Motor ESC T40A, 2 4S LiPo 5000mAh

As part of this set we offer a copter that already possesses all of the components in its initial configuration that are necessary for a stable support system to transport various payloads.

The copter can be expanded at any time to, in conjunction with a gimbal of the CM-M make, later be operated as an AirJib (AJ6-800-BAJ, AJ6-800-AAJ).

We recommend this set if you would first like to familiarize yourself with the AF6-800 copter and then decide at a later time which version of the CM-M gimbal is most suitable to your needs.

The basic air frame comes with the damping system AF6-800-DPC and the mounting frame AF6-800-MFR. By employing the optionally available pipe clamps GPI-BC12 and a suitable adapter you can attach for example a gimbal made by a third party provider to it.

Alternatively you can also install the universal mounting plate AF6-800-UMP on the damping system, which is not included in the delivery contents.

The set consists of the following components.

• AF6-800-FRM (base frame)
• AF6-800-PDB (power distribution plate)
• AF6-800-LGC (landing gear)
• AF6-800-BHC (battery holder)
• AF6-800-DPC (damping system)
• AF6-800-MFR (mounting frame)

Technical Specifications
Weight: 862g
Dimensions (L x B x H): 846 x 846 x 380mm

Delivery Contents
1 piece AF6-800-FRM (base frame)
1 piece AF6-800-PDB (power distribution plate)
1 piece AF6-800-LGC (landing gear)
1 piece AF6-800-BHC (battery holder)
1 piece AF6-800-DPC (damping system)
1 piece AF6-800-MFR (mounting frame)
1 set assembly material

Recommended Drives
T-Motor MN3110 KV470 with T-Motor 15x5.0" CFK propeller and T-Motor ESC T40A, 2 4S LiPo 5000mAh
T-Motor MN3508 KV580 with T-Motor 14x4.8" CFK propeller and T-Motor ESC T40A, 2 4S LiPo 5000mAh
T-Motor MN3510 KV700 with T-Motor 13x4.4" CFK propeller and T-Motor ESC T40A, 2 4S LiPo 5000mAh

The set CM-M CameraMount S3D consists of the gimbal CM-M-G3D in combination with the hand frame CM-M-HFR and is fitted with the following components.

• CM-M-G3D (gimbal)
• CM-M-HFR (hand frame)
• CM-M-GAA (gimbal adapter type A)
• CM-M-COA (controller holder type A)
• CM-M-CAA (camera holder type A)

Important information
Basecam Alexmos brushless gimbal electronics is not included!

Technical Specifications
Weight: 1127g
Dimensions (L x B x H): ca. 450 x 405 x 200mm

Delivery Contents
1 piece CM-M-G3D (gimbal)
1 piece CM-M-HFR (hand frame)
1 piece CM-M-GAA (gimbal adapter type A)
1 piece CM-M-COA (controller holder type A)
1 piece CM-M-CAA (camera holder type A)

The set CM-M CameraMount S3S consists of the gimbal CM-M-G3S in combination with the hand frame CM-M-HFR and is fitted with the following components.

• CM-M-G3S (gimbal)
• CM-M-HFR (hand frame)
• CM-M-GAA (gimbal adapter type A)
• CM-M-COB (controller holder type B)
• CM-M-CAA (camera holder type A)

Important information
Basecam Alexmos brushless gimbal electronics is not included!

Technical Specifications
Weight: 1058g
Dimensions (L x B x H): ca. 450 x 405 x 200mm

Delivery Contents
1 piece CM-M-G3S (gimbal)
1 piece CM-M-HFR (hand frame)
1 piece CM-M-GAA (gimbal adapter type A)
1 piece CM-M-COB (controller holder type B)
1 piece CM-M-CAA (camera holder type A)

The set CM-M CameraMount S2D consists of the gimbal CM-M-G2D in combination with the hand frame CM-M-HFR and is fitted with the following components.

• CM-M-G2D (gimbal)
• CM-M-HFR (hand frame)
• CM-M-GAA (gimbal adapter type A)
• CM-M-COA (controller holder type A)
• CM-M-CAA (camera holder type A)

Important information
Basecam Alexmos brushless gimbal electronics is not included!

Technical Specifications
Weight: 929g
Dimensions (L x B x H): ca. 450 x 405 x 200mm

Delivery Contents
1 piece CM-M-G2D (gimbal)
1 piece CM-M-HFR (hand frame)
1 piece CM-M-GAA (gimbal adapter type A)
1 piece CM-M-COA (controller holder type A)
1 piece CM-M-CAA (camera holder type A)

The set CM-M CameraMount S2S consists of the gimbal CM-M-G2S in combination with the hand frame CM-M-HFR and is fitted with the following components.

• CM-M-G2S (gimbal)
• CM-M-HFR (hand frame)
• CM-M-GAA (gimbal adapter type A)
• CM-M-COB (controller holder type B)
• CM-M-CAA (camera holder type A)

Important information
Basecam Alexmos brushless gimbal electronics is not included!

Technical Specifications
Weight: 861g
Dimensions (L x B x H): ca. 450 x 405 x 200mm

Delivery Contents
1 piece CM-M-G2S (gimbal)
1 piece CM-M-HFR (hand frame)
1 piece CM-M-GAA (gimbal adapter type A)
1 piece CM-M-COB (controller holder type B)
1 piece CM-M-CAA (camera holder type A)

The base frame is the central component of the quadrocopter AF4-350-3D. Since its motor axes distance is 350mm, propellers with a maximum diameter of 9.5” can be used.

The frame consists of seven CNC-milled carbon plates of the highest quality that are connected by only 12 screws. This makes the copter extremely lightweight at only 120g (excluding the rubber elements that come with it) while maintaining highest possible stability. Two breadboards – 45 x 45mm and 30.5 x 30.5mm – also allow for the integration of mini control systems such as the NAZE32 by AbuseMark or the NanoWii by Flyduino.

The centerplates are designed in such a way to minimize the overall weight through recesses while simultaneously leaving enough surface area to securely fasten the electrical components.

An additional plate, mounted above the upper centerplate, increases stability even more and protects the valuable electronics against possible damage.

Both the arms as well as all plates consist of CFRP pressed at high temperatures. This material provides for maximum solidity while remaining at an extremely low weight.

This frame comes with a complete assembly kit. All screws and nuts are made of type A4 stainless steel.

The nuts used here are exclusively so-called press nuts. Using special tools they are being molded into the CFRP-plates which allows for easy assembly without the use of screw wrenches or pliers.

The lower centerplate already contains all of the press nuts that are necessary to assemble the components in all possible configurations.

This frame was mainly designed for sophisticated acrobatic flights, including 3D mode, and will even be able to survive crashes at a very high velocity without parts being damaged. If an arm or a centerplate does happen to get damaged it is no problem to order a single replacement piece.

We recommend that especially beginners or lesser experienced pilots opt to install the motor protection plates (AF4-350-3D-MPP) that can easily be removed again at any time.

Four optionally mountable supporting feet (AF4-350-3D-LLG) are also part of the system and offer support during take off and landing.

The plates are made of high-strength CFRP.

Technical Specifications
Type: quadrokopter
Diagonal wheelbase: 350mm
Weight: 120g (excluding the rubber elements that come with it)
Engine mount: 16-19mm (slot holes)
Dimensions (L x B x H): 390 x 390 x 30mm

Delivery Contents
2 pieces carbon centerplates (AF4-350-3D-CPT, AF4-350-3D-CPB)
1 piece carbon protective plate for electronics (AF4-350-3D-PPE)
4 pieces carbon plates for arms (AF4-350-3D-ARM)
4 pieces rubber dampers
1 set assembly material

Recommended Drives
T-Motor AirGear 350 (Multirotor Driving Equipment Set), 1 3S LiPo 2600mAh
T-Motor MT2208-18 KV1100 with T-Motor 8x4,5" propeller and T-Motor ESC AIR 15A, 1 3S LiPo 2600mAh
Hacker A20-26M EVO (1130kv) with 8x4,5" propeller and T-Motor ESC AIR 15A, 1 3S LiPo 2600mAh